Female thread pot magnets are the hanging option in the pot magnet range. A NdFeB ring magnet sits in a nickel-plated steel shell, and a tapped boss rises from the back — you screw a hook, eyebolt, knob or rod end into the bore instead of bolting the magnet to something.
This page covers our female thread pot magnets in full: 11 stock sizes from 10 mm to 75 mm diameter with M3–M10 tapped bores, real measured pull force up to 250 kgf, and the one dimension chain almost no listing explains — total height equals cup height plus thread depth on every single size (verify it in the table below), which makes thread engagement a design input rather than a surprise.

A female thread pot magnet (also called an internal thread pot magnet or a tapped pot magnet) is a neodymium ring magnet in a steel shell whose back carries a raised boss with a tapped blind bore. The thread is female: a bolt screws into the magnet, so a load can hang from it, or an accessory — hook, eyebolt, knob, rod end — can be attached to it.
In female thread pot magnets the steel shell does the same job as in every pot magnet: it closes the magnetic circuit behind the magnet, so nearly all flux exits the working face, and the field on the back and sides is nearly zero. The bore costs a little magnet volume — the trade you make for a thread instead of a hole.
The female thread category runs from 10 mm to 75 mm — the smallest starting size of any pot series we make:
| D × cup H | Total H | Thread × depth | Weight | Pull force |
|---|---|---|---|---|
| 10 × 5 mm | 12 mm | M3 × 7 mm | 3 g | 4.19 lb (1.9 kgf) |
| 12 × 5 mm | 12.5 mm | M3 × 7.5 mm | 4 g | 7.28 lb (3.3 kgf) |
| 16 × 5 mm | 13 mm | M4 × 8 mm | 7.5 g | 9.26 lb (4.2 kgf) |
| 20 × 6 mm | 14 mm | M4 × 8 mm | 13 g | 11.02 lb (5 kgf) |
| 25 × 7 mm | 16 mm | M5 × 9 mm | 24 g | 24.25 lb (11 kgf) |
| 32 × 7 mm | 15 mm | M6 × 8 mm | 39 g | 44.09 lb (20 kgf) |
| 36 × 7 mm | 15 mm | M6 × 8 mm | 46 g | 48.5 lb (22 kgf) |
| 42 × 8 mm | 15 mm | M6 × 7 mm | 85 g | 77.16 lb (35 kgf) |
| 48 × 11 mm | 24 mm | M8 × 13 mm | 154 g | 165.35 lb (75 kgf) |
| 60 × 15 mm | 30 mm | M8 × 15 mm | 326 g | 308.65 lb (140 kgf) |
| 75 × 18 mm | 34 mm | M10 × 16 mm | 618 g | 551.16 lb (250 kgf) |
All 11 female thread pot magnets are axially magnetized, nickel-plated, ±0.5 mm tolerance, 80 °C standard, with a bare steel working face. Larger diameters, stainless builds and imperial threads are made to drawing via custom magnets; the standard vs custom guide explains when that is worth it.
Read down the table and a rule jumps out: total height minus cup height equals the thread depth, on all 11 sizes. 10 mm pot: 12 − 5 = 7 mm bore. 48 mm pot: 24 − 11 = 13 mm bore. 75 mm pot: 34 − 18 = 16 mm bore. The boss is exactly as tall as the thread is deep — the screw-thread engagement you get is fixed by the boss, not by the bolt. Every one of the 11 female thread pot magnets follows the rule; test any row against your own drawing.
That gives you two numbers to design around, not one:
| Thread | Bore depth | Bolt engagement to aim for | Used on |
|---|---|---|---|
| M3 | 7 – 7.5 mm | 5 – 6 mm (full thread, leave one pitch) | 10 / 12 mm |
| M4 | 8 mm | 6 – 7 mm | 16 / 20 mm |
| M5 | 9 mm | 7 – 8 mm | 25 mm |
| M6 | 7 – 8 mm | 5.5 – 7 mm | 32 / 36 / 42 mm |
| M8 | 13 – 15 mm | 10 – 13 mm | 48 / 60 mm |
| M10 | 16 mm | 13 – 14 mm | 75 mm |
Three practical rules:
Female thread pot magnets put the thread inside the boss; the T3 series carries the same idea in reverse — a stud sticks out, the magnet screws into your part. Choose by where the thread needs to be:
| Female thread (T4) | External thread (T3) | |
|---|---|---|
| Thread sits | inside the boss (load hangs from magnet) | on the outside (magnet hangs on load) |
| Accessory | hook, eyebolt, knob, rod end | bracket, ball joint, arm |
| Face | bare nickel — full pull | rubber-jacketed — grip over pull |
| Diameter range | 10 – 75 mm | 22 – 88 mm (rubber-coated) |
| Adjustability | rotate the accessory only | aim the whole magnet |
Rule of thumb: if the thing you attach must point a particular way and the magnet sticks to steel, external thread; if the magnet sticks to steel and something hangs from it, female thread. Rubber-coated female versions also exist in the rubber-coated magnets family — for example the 43 mm M4, 66 mm M6 and 88 mm M6 — when you need the grip but not the stud.

Even with the bore stealing a little volume, female thread pot magnets follow the same geometry laws as the rest of the pot family — and they hold hard:
| Size | Pull force | Surface gauss | Pull per gram |
|---|---|---|---|
| 10 × 5 mm | 4.19 lb | ~3,300 Gs | 1.40 lb/g |
| 16 × 5 mm | 9.26 lb | ~3,300 Gs | 1.23 lb/g |
| 25 × 7 mm | 24.25 lb | ~2,500 Gs | 1.01 lb/g |
| 36 × 7 mm | 48.5 lb | ~1,000 Gs | 1.05 lb/g |
| 48 × 11 mm | 165.35 lb | ~900 Gs | 1.07 lb/g |
| 75 × 18 mm | 551.16 lb | — | 0.89 lb/g |
Three patterns in the female thread pot magnets range:
Diameter explodes the pull. From 10 mm to 75 mm is a 7.5× diameter increase — and a 131× pull increase. Pull area grows with the square of diameter, and the taller bodies (5 → 18 mm) feed the circuit more magnet, so the large pots over-deliver. A 618 g part holds a quarter of a tonne.
Surface gauss collapses as pull climbs. The 10 mm pot reads ~3,300 Gs and holds 4.19 lb; the 48 mm pot reads ~900 Gs and holds 165 lb — 39× the pull at a quarter of the point reading. Gauss is a spot measurement on the pole face, not a capacity: order female thread pot magnets by the pull column, never by gauss. Background in how to measure surface gauss with a gaussmeter and identical volume, different pull.
The bore costs about 10% against the through-hole series. At matching diameters, these pots sit within roughly ±10% of the T1 countersunk series — identical at 48 mm (165.35 lb in both), 8% stronger at 60 mm, 6% stronger at 75 mm — except the 20 mm pot, which gives up 29% because the M4 boss takes a proportionally bigger bite of a small magnet. If your design needs every gram of pull at small diameters, a screw-through pot wins; the moment the load hangs from a thread, the T4 series is the right tool.
Catalog pull is direct pull off thick, clean, flat steel. Four factors change what female thread pot magnets deliver in service:
The ring magnets inside female thread pot magnets are sintered NdFeB in the N42-class range — the grade property table shows why grade matters less inside a closed shell than in a bare magnet. Standard rating is 80 °C continuous; above that the magnet loses pull reversibly at first, then permanently. For oven or engine-bay duty, ask about higher-temperature builds via custom magnets; the Curie temperature guide and temperature stability overview cover the physics.
All 11 female thread pot magnets are axially magnetized: one pole on the working face, the other closed into the shell — the standard pot magnet orientation that makes the cup multiply front-face pull. Multi-pole and diametrical arrangements are possible in custom assemblies.
Every part in the female thread pot magnets range ships nickel-plated (Ni-Cu-Ni) — the standard NdFeB surface treatment, adequate for dry indoor service and the reason these pots keep their full bare-face pull. For humidity, salt spray or outdoor duty, move to epoxy or a rubber-jacketed version from the rubber-coated range; the coating selection guide and the coatings explainer compare every option. Remember the trade: a rubber jacket adds a non-magnetic gap and cuts direct pull by roughly 20–30%, which is why the T4 series stays bare.
The tapped bore decides the application list for female thread pot magnets — anywhere a load hangs or an accessory must be attached:
More use cases across the range: 15 key industrial NdFeB applications.
Send us five items and quoting is same-day, following the procurement requirement guide:
Two spec traps worth naming: quote total height (cup + boss), not just cup height, and confirm thread depth, not only thread size — the depth varies from 7 mm at M3 to 16 mm at M10. Dimensional expectations follow NdFeB tolerance standards; ±0.5 mm on diameter and height covers all stock female thread pot magnets.
A neodymium ring magnet in a nickel-plated steel shell, with a tapped blind bore in a raised boss on the back. A bolt, hook, eyebolt or knob screws into the magnet, so loads hang from it while the bare face grips steel — that construction is what separates female thread pot magnets from the through-hole and stud versions of the family.
From 4.19 lb (1.9 kgf) at 10 mm to 551.16 lb (250 kgf) at 75 mm, measured as direct pull from thick flat steel. Hanging loads add a lever effect, so keep the load line close to the magnet axis.
M3 on the 10 and 12 mm pots, M4 on 16 and 20 mm, M5 on 25 mm, M6 on 32 to 42 mm, M8 on 48 and 60 mm, and M10 on the 75 mm pot. Bore depth runs from 7 mm at M3 to 16 mm at M10 — the full mapping for female thread pot magnets is in the tables above.
Because the tapped boss on the back is exactly as tall as the thread is deep — total height = cup height + thread depth, on all 11 sizes. That is why a 48 mm pot measures 24 mm tall, not 11 mm.
If the load hangs from the magnet or an accessory attaches to it, female thread (T4). If the magnet must screw into a bracket or arm you aim, external thread (T3). The T3 series is rubber-coated; T4 keeps the bare nickel face for full pull.
Within about ±10% at matching diameters — identical at 48 mm, slightly stronger at 60 and 75 mm, and about 29% weaker at 20 mm where the boss takes more of the magnet. Choose by how the part mounts, not by a few percent of pull.
Gauss is a point reading on the pole face. The large pots spread their field over a much bigger area at lower intensity — and hold far more. Order female thread pot magnets by pull force, never by surface gauss.
Yes — bore depth, thread size and boss height are all made to drawing. If your accessory needs more engagement than the stock depth, ask for a custom build with the depth you need.
80 °C continuous as standard. Higher-temperature grades and coatings are available as custom builds; see the Curie and operating temperature guide for the physics.
Yes. Every stock size has tiered pricing, custom threads and depths are made to drawing, and mixed female/external thread orders ship together from the same production line.
Browse the full female thread pot magnets category for live pricing on all 11 sizes, or send your thread, load case and environment through contact us — we will match the bore, the boss and the diameter to your assembly. For a stud instead of a bore, the T3 threaded series covers 22–88 mm; for a screw-through mount, the T1 and T2 series; and for the family overview start at pot magnets.